Nearly every job in a fabrication shop or print shop starts with a cut. This guide helps fabricators, sheet metal shops, steel stockists and print finishers pick between a band saw, CNC plasma, laser, shear and paper cutter. It also covers new versus used and the details a supplier needs.
Types of cutting machines and what each is for
Band saw machine (metal)
A metal band saw pulls a continuous toothed blade through bar, tube, pipe, structural sections and solid blocks. Horizontal models cut stock to length; vertical models allow contour cuts guided by hand. Pick a band saw when your raw material is bar or section, not sheet. The cut is cold, the kerf is narrow and little material is wasted.
CNC plasma cutting machine
A CNC plasma machine cuts electrically conductive metal with a jet of ionised gas that follows a programmed path over a cutting table. It is quick on medium and thick steel plate and also cuts stainless steel and aluminium. The edge is rougher than a laser edge. Choose plasma for fabrication and structural parts where plate is thick, tolerances are moderate and the budget will not stretch to a laser.
Laser cutting machine
A laser cutting machine uses a focused beam to cut a narrow, clean line with fine detail and small holes. It is strongest on thin and medium sheet, where parts need little finishing. Fibre lasers are the usual choice for metal; CO2 lasers are widely used for non-metals such as acrylic and wood. Pick a laser when accuracy, edge quality or intricate shapes matter, and expect a higher purchase cost.
Metal shearing machine
A shearing machine makes straight cuts across sheet or plate by driving a moving blade past a fixed one. A back gauge sets the cut length, so identical strips and blanks come off quickly. It is a fast, low-cost way to produce rectangles for bending and pressing. It cannot cut curves or internal openings.
Paper cutting machine
A paper cutting machine is a guillotine for stacks of paper, board and labels. A clamp holds the stack, a knife descends, and a back gauge positions each cut. Printers, binders and packaging units use it for trimming and cutting to size. It is chosen by sheet size and stack height.
| Your work | Usual choice |
|---|---|
| Bar, pipe and sections cut to length | Band saw machine |
| Shapes from thick plate, moderate accuracy | CNC plasma cutting machine |
| Detailed shapes from thin or medium sheet | Laser cutting machine |
| Straight blanks and strips from sheet | Metal shearing machine |
| Stacks of paper or board | Paper cutting machine |
How to choose: the points that decide it
- Material. Plasma works only on conductive metals. Reflective metals and non-metals affect which laser type fits. A shear handles less thickness in stainless than in mild steel.
- Thickness and size of work. The thickest regular job and the largest sheet or section set the capacity and table size.
- Shape. Straight cuts suit a saw or shear. Profiles and cut-outs need plasma or laser.
- Accuracy and edge quality. Do not pay for laser quality on edges that will be welded over or hidden.
- Batch size. Occasional cutting can be manual. Daily volume justifies automatic feed, CNC and nesting software.
- Conventional or CNC. A manual saw or shear is easy to own. CNC plasma and laser need digital drawings and someone to prepare programs.
- Power supply and utilities. Check phase and load. Plasma and laser may also need compressed air, assist gas, a chiller and fume extraction.
- Floor space. Include room to load full sheets or long bars and to unload cut parts and scrap.
- Operator skill. Thermal cutting needs training in settings, consumables and safety. Shears and guillotines need strict guarding discipline.
- Budget and running cost. Blades, nozzles, electrodes, lenses, gas and power are ongoing costs. Weigh them with the purchase price.
New or used: a fair comparison
New is the safer route for laser machines and for any machine that will carry your main production. New machines on MachineryInsider have a 12-month warranty. Browse new cutting machines to see what is listed.
Used is often sensible for band saws, shears and paper cutters, which are robust and simple to assess. Used plasma and laser machines can save a lot of capital, but the condition of the power source or laser source matters more than the frame. With used cutting machines, the year and condition are confirmed on enquiry, and the buyer can inspect the machine before paying. Check these items:
- Guides, rails and slideways. Look for wear on saw blade guides, on the gantry rails and drives of plasma and laser tables, and on shear blade guides.
- Blades and knives. Check shear blades and paper knives for chips, and confirm the blade gap adjusts.
- Cutting source. Ask for the service history of a plasma power source or laser source. Inspect the torch or cutting head, optics and chiller.
- Backlash and squareness. Cut a test square and measure it.
- Running under load. See it cut your material at your thickness, not a thin demo piece.
- Electricals, controller and software. Test every function. Confirm the controller is supported and software licences transfer with the machine.
- Safety devices and spares. Guards, light curtains and emergency stops must work, and consumables must still be available.
- Paperwork. Ask for the invoice, proof of ownership and written confirmation that no loan is outstanding on the machine.
If you are upgrading, you can sell your machine on MachineryInsider as well.
What to send a supplier to get an accurate quote
- Materials you cut and the thickness range for each.
- Largest sheet, plate, bar or paper size you handle.
- Sample drawings or photos of typical parts.
- Edge quality and tolerance needed.
- Daily or monthly cutting volume.
- Power, compressed air and gas available at your site.
- Delivery location and whether on-site installation is needed.
Send it through request a quote. Prices are on request, and a quote comes back within 4 working hours.
Common mistakes to avoid
- Sizing the machine for a rare thick job instead of the daily work.
- Comparing purchase prices and ignoring consumables, gas and power.
- Buying plasma when parts need laser accuracy, or laser when a shear would do.
- Leaving fume extraction, compressed air or a chiller out of the plan.
- Buying a used machine with missing safety guards or unclear ownership.
Frequently asked questions
Which is better, plasma cutting or laser cutting?
Neither is better in every case. Laser gives a cleaner edge and finer detail, mainly on thin and medium sheet. Plasma costs less to buy and handles thick plate well, with a rougher edge.
What is the difference between a shearing machine and a band saw?
A shear cuts flat sheet and plate in straight lines with a blade stroke. A band saw cuts bar, pipe and sections with a moving toothed blade.
Is it worth buying a used laser cutting machine?
It can be, if the laser source, cutting head and chiller are in good order and the controller is supported. Ask for service records and insist on a test cut in your own material.
Which machine do I need to cut paper in bulk?
A paper cutting machine, also called a guillotine. Choose it by your largest sheet size and stack height. A programmable model saves time when jobs have many cut sizes.
Decide the material, thickness and shape first, and the machine type follows. Compare new cutting machines with used cutting machines, or request a quote and describe your work. Every purchase comes with a tax invoice. Delivery is arranged worldwide, remote installation support is included, and on-site installation can be requested.