This guide is for factory owners, first-time buyers and purchase managers who need a plastic processing machine. It explains the main machine types, the questions that decide which one fits your product, how new and used machines compare, and what a supplier needs from you to quote properly.
Types of plastic and moulding machines and what each is for
Every plastic machine melts raw material and gives it a shape. How the shape is formed decides which products a machine can make.
Injection Moulding Machine
An injection moulding machine melts plastic granules and forces the melt into a closed mould, where it cools into a finished part. It makes solid, detailed items such as caps, crates, buckets, toys, switch housings and automotive parts. Choose it when your product is a solid part with a fixed shape that must repeat exactly over long runs. The mould is a separate cost and often decides the machine size, so plan both together.
Blow Moulding Machine
A blow moulding machine makes hollow products. It extrudes a hot tube of plastic, closes a mould around it and inflates it with air. Typical output includes shampoo and detergent bottles, jerry cans, lubricant containers, drums and water tanks. Pick it over injection moulding when the product is hollow with a narrow neck, or needs a moulded handle.
Extrusion Machine
An extruder pushes molten plastic through a die in a continuous stream. The product has the same cross-section along its whole length: film, sheet, profiles, tubing, cable coating or recycled granules. It suits you when you sell by length or weight rather than by piece. The die, cooling, haul-off and winding or cutting units matter as much as the extruder itself.
PVC Pipe Making Machine
This is an extrusion line built specifically for pipe. It normally combines an extruder suited to PVC compound, a pipe die, a vacuum sizing and cooling tank, a haul-off, a cutter and often a socketing unit. It produces plumbing pipe, electrical conduit, and agricultural and drainage pipe. Buy a dedicated pipe line if pipe is your main product, because the downstream equipment sets the diameter range and wall quality.
PET Bottle Making Machine
A PET bottle machine heats ready-made preforms, then stretches and blows them into clear bottles and jars. It is the usual choice for drinking water, soft drink, juice and edible oil bottles. Semi-automatic models suit small bottlers, and fully automatic models suit steady, high-volume filling lines. It needs a high-pressure air compressor and a chiller, and you must either buy preforms or mould them yourself.
How to choose the right machine
Answer these questions before you look at any listing. Write the answers down, because they become your specification.
- Product: Decide exactly what you will make. Have a sample or drawing with dimensions, weight and wall thickness.
- Output: Work out the pieces or weight you need per shift, with sensible room for growth.
- Material: Name the polymer and whether it is virgin or recycled. PVC, PET, polyethylene and polypropylene each need a suitable screw, barrel and temperature control.
- Moulds and dies: If you already own tooling, the machine must accept its size, weight and mounting.
- Automation: Manual, semi-automatic or fully automatic. More automation means fewer operators and steadier quality, but higher cost and more skilled maintenance.
- Power and utilities: Check the connected load sanctioned at your site, plus cooling water, chiller and compressed air needs.
- Floor space: Measure the bay, door openings and floor strength. Extrusion lines are long and injection machines are heavy.
- Operator skill: A simpler control system is safer if trained setters are hard to find locally.
- Budget: Include the mould, auxiliaries, transport, installation and working capital for raw material, not only the machine price.
New or used: an honest comparison
A new machine makes sense when you have confirmed orders, run long hours, or need tight tolerances and low energy use per part. On MachineryInsider, new plastic and moulding machines carry a 12-month warranty.
A used machine makes sense when capital is tight, the product is simple, you are testing a new market, or you need a standby line. The risk is hidden wear, so inspect before you pay. Browse the used plastic and moulding machines and check the following on any machine you shortlist:
- Running under load: See it make real parts with material and a mould fitted, not just idle cycles.
- Wear parts: Screw and barrel, tie bars, platens, toggle pins and bushes, heater bands and thermocouples.
- Hydraulics: Oil leaks, pump noise, hose condition and cylinder seals.
- Electricals and controller: Panel wiring, contactors, display and keys, and whether the controller model is still supported.
- Spares: Confirm that seals, heaters, controller cards and screw sets are still available.
- Paperwork: Ask for the original invoice and manuals. Find out whether a loan is still open on the machine, and get a clearance letter if so.
For used machines on the site, the year and condition are confirmed on enquiry, and you can inspect the machine before paying. If you are replacing an older machine, you can also list your machine for sale to recover part of the cost.
What to send a supplier to get an accurate quote
Vague enquiries get vague prices. Send these details with your request:
- Product name, a photo or drawing, dimensions and part weight.
- Raw material, and whether you will use recycled content.
- Required output per hour or per shift.
- Number of cavities, or details of the mould or die you already have.
- New or used preference, and the level of automation you want.
- Available power supply and any limit on connected load.
- Auxiliaries needed: chiller, compressor, dryer, hopper loader, grinder.
- Delivery location, and whether you need on-site installation.
Common mistakes to avoid
- Choosing on price alone and ignoring energy use, rejection rate and downtime.
- Buying the machine first and then finding the mould does not fit it.
- Forgetting auxiliaries. A PET line without the right compressor will not run.
- Accepting a used machine on photos and video without seeing it under load.
- Skipping the paperwork check and learning later that a lender has a claim on the machine.
Frequently asked questions
Which plastic moulding machine is best for a small business?
It depends on the product, not on the size of the business. For solid items, a small injection moulding machine is the usual start. For water or juice bottles, a semi-automatic PET bottle machine keeps the investment and skill level low.
What is the difference between injection moulding and blow moulding?
Injection moulding fills a closed mould with molten plastic to make solid parts. Blow moulding inflates hot plastic inside a mould to make hollow parts such as bottles and cans. If the product holds liquid and has a neck, it is almost always blow moulded.
Is it safe to buy a used injection moulding machine?
Yes, if you inspect it properly. Watch it run under load, check the screw, barrel, tie bars and hydraulics, confirm that controller spares exist, and verify the invoice and loan status. Walk away if the seller will not allow a trial run.
How much does a plastic moulding machine cost?
The price depends on type, size, automation level, age and the auxiliaries included, so a single figure would mislead you. Prices on MachineryInsider are on request, and quotes are sent within 4 working hours once you share your requirement.
Next steps
Fix your product, output and material first. Then compare the new machine listings with the used machine listings. When your specification is ready, request a quote. A tax invoice is issued with every purchase, delivery is arranged worldwide, and remote installation support is included, with on-site installation available on request.